WhatsApp ไธญๆ–‡ ะ ัƒััะบะธะน

Why Pressure Cascades Matter

In multi-zone cleanroom environments โ€” a hospital's OR suite, a pharmaceutical facility's GMP production areas, or a semiconductor fabrication plant โ€” each room or zone operates at a controlled pressure differential relative to adjacent zones. The cascade must be designed so that cleanest air flows from the cleanest zone to the least clean, and exhaust air does not backflow into clean zones. If the cascade fails, cross-contamination risk rises immediately.

Determining the Pressure Hierarchy

Before any fan or AHU selection, the pressure map must be defined:

  • Positive pressure cascade โ€” cleanest zone (e.g., ISO 5) at the highest pressure; air flows outward to less clean zones and finally to exhaust. Used for product-protective processes (pharma, electronics, food packaging).
  • Negative pressure cascade โ€” contaminated zone (e.g., isolation room, vaccine storage) at the lowest pressure; air flows inward from adjacent zones through HEPA-filtered supply, preventing contaminated air from escaping. Used for infection control (hospital isolation, biosafety labs).
  • Hybrid cascade โ€” some zones positive, some negative, with a neutral buffer zone in between. Common in hospital operating theatres where ORs are positive and isolation rooms are negative.

Typical pressure differential targets:

  • Between cleanroom zones: 5-15 Pa (ยฑ10% control tolerance)
  • Between cleanroom and corridor: 15-25 Pa
  • Isolation room to corridor: -10 to -15 Pa

Fan Selection for Pressure Cascade Systems

The supply and exhaust fans must operate at stable, precise airflow rates to maintain the pressure map. Variable frequency drive (VFD) or EC fan control is essential โ€” fixed-speed fans cannot adjust to changes in door opening, filter loading, or seasonal outdoor air conditions. For hospitals, fail-safe operation is critical: if the power supply to a VFD is lost, the fan must not shut down completely, or the pressure differential will collapse.

Key fan specifications:

  • Supply fans: high-volume, low-static-pressure centrifugal or plug fans with VFD control; airflow matched to the room volume and required ACH
  • Exhaust fans: medium to high static pressure axial or centrifugal fans, with HEPA exhaust filters at the exhaust termination
  • Balance: supply + exhaust must sum to the required room ACH; a 10% excess exhaust (common for negative pressure rooms) must be compensated by make-up air

Pressure Sensor Placement and Control Logic

Each room requires at least one differential pressure sensor (DP sensor) near the door frame or at the room's geometric centre, not near a door or air supply outlet (both of which create localised pressure disturbances). The DP sensor signal feeds into the BMS, which adjusts supply and exhaust VFD speeds to maintain the target differential. Control logic must include:

  • Fail-safe mode: on VFD fault, the system must default to the safe direction of airflow (for isolation rooms, increase exhaust; for cleanrooms, reduce supply)
  • Alarms: differential pressure out of range for more than 5 minutes triggers an audible and visual alarm
  • Logging: continuous DP logging for regulatory audit (GMP and ISO 14644 inspections)

Validation and Documentation

Before the cleanroom goes into service, a full pressure cascade validation protocol must be executed: each room is sealed, DP sensors calibrated, and the system run for a minimum 48-hour stability period under all combinations of door open/close, filter replacement, and seasonal outdoor air. The as-built DP map and sensor calibration records become part of the facility's quality management documentation and are inspected by GMP and ISO 14644 auditors.

Keruite supplies the complete supply/exhaust fan package for cleanroom projects, including VFD control, DP sensor integration, and as-built documentation for GMP and ISO 14644 submission.

View our cleanroom and hospital AHU range โ†’

Share this article:

Need Help Selecting the Right Equipment?

Our engineering team provides free consultation on fan selection, system design, and technical specifications.

Request a Technical Proposal Browse Products

Related Articles

Industrial Ventilation System Design: Components and Process... →